What Size Pump Do I Need To Lift Water 400 Ft

Well Pump Capacities in GPM or Water Delivery Rates
Pump capacity charts & calculations for jet pumps & submersible pumps

• POST a QUESTION or Annotate about water well pump size, horsepower, & pumping chapters requirements & water flow rates

InspectAPedia tolerates no conflicts of involvement. Nosotros have no human relationship with advertisers, products, or services discussed at this website.

Water well pump types, models, pumping capacities:

This article compares the pumping capacity in gallons per minute (GPM) of ane line jet pumps, two line jet pumps, submersible pumps, and well pumps of dissimilar models and horsepower.

This article includes well pump chapters and model example tables from well pump installation manuals provided past the Water Ace Corporation. [permission requested]

We besides provide an ARTICLE Index for this topic, or y'all can try the folio meridian or bottom SEARCH BOX every bit a quick fashion to find information y'all need.

What is the Pumping Capacity in Gallons per Minute for a ane-Line Shallow Well Jet Pump?

A one-line jet pump can typically heighten water from depths of just a few feet (or "0" depth) to nigh 25 anxiety in depth.

Typical shallow well jet pumps sport h2o delivery rates from iv gpm or 15 liters per minute (lpm) upward to equally much as 25 gpm (95 lpm) depending on the variables we list below the well pump capacity tables shown.

Shallow Well Pump Capacity Charts

A squeamish example table of shallow well 1-Line Jet Pump Capacities for 1/2 hp, iii/four, and 1 hp shallow well pumps is provided in the Water Ace Jet Pump Installation Manual cited at the end of this article and excerpted here to illustrate the factors that decide well pump chapters.

The two shallow well pump capacity charts higher up & below are for i-line jet pumps produced by Water Ace.

1-Line jet pumps intended for shallow well use and fabricated by other manufacturers can be expected to accept similar capacities.

[Click to enlarge any image or table]

What Determines the Water Delivery Capacity of a Well Pump?

The Water Ace charts (shown in part above) make articulate that the capacity of a one-line shallow well jet pump to evangelize water at a given flow rate varies by these factors:

1. The depth of the well (the bottom scale in the ii charts)
2. The pump horsepower (the color codes indicate pump model and horsepower HP variation)
3. The well pump model and number of stages and therefore pump type and internal blueprint

   The 2d shallow well pump capacityy table shown just higher up is for the visitor'due south more powerful well pump serial of 2-line jet pumps.

   The pump "model" for college chapters output h2o pumps will include a number of well pump stages (to well over 20 in some cases) that increase the pump'due south lift and output force per unit area capacity.

4. The condition of well piping, including pipe diameter, length, number of bends or elbows
5. Leaks in the water organization: the presumption that the entire pipage arrangement has no leaks
6. The flow rate of the well: for limited flow-rate wells at which a pump protection device is installed (to prevent the pump from running dry and thus being damaged), equally the well menstruation rate diminishes during employ, the water delivery rate may also drop.

Permission requested, Water Ace Corp. Aug 2010 - Pentair Pump Group.

Lookout Out: Safety warnings are throughout any pump manufacturer'due south instructions. Because some pump models are capable of developing internal pressures of more than 100 psi, if your building piping, force per unit area relief valves, prophylactic controls, wiring, and plumbing are not properly installed, very dangerous conditions including electrical shock, tank explosion, and leaks or floods tin can occur.

What is the Pumping Capacity in Gallons per Infinitesimal for a 2-Line Deep Well Jet Pump?

A two-line jet pump can typically enhance water from depths of 30 feet to 80 feet, and at h2o delivery rates of 4 gpm (for a 1/two hp 2-line jet pump serving an 80 pes deep well) to xvi gpm (for a 1 hp two-line jet pump serving a 30 pes deep well).

Deep Well Jet Pump Chapters Charts

A nice instance table of Deep Well 2-Line Jet Pump Capacities for 1/2 hp and ane hp deep well pumps is provided in the Water Ace Jet Pump Installation Transmission and excerpted above & beneath to illustrate the factors that determine well pump capacity.

Both of the charts below are for ii-line jet pumps produced by Water Ace. 2-line jet pumps intended for deep well use and made by other manufacturers tin be expected to have similar capacities.

The Water Ace charts (shown in office above) make clear that the capacity of a deep well pump to deliver water at a given flow rate varies by pretty much the same factors equally those we listed for shallow wells and well pumps.

1. The depth of the well (the lesser scale in the two charts)
2. The pump horsepower (the colour codes indicate pump model and horsepower HP variation)
3. The well pump model and therefore pump type and internal pattern

   The second of the two deep well pump chapters tables is for the company'southward more powerful well pump series of ii-line jet pumps.

4. The status of well piping, including pipe diameter, length, number of bends or elbows
5. Leaks in the water arrangement: The presumption that the entire piping system has no leaks
6. The flow rate of the well: for limited menstruation-rate wells at which a pump protection device is installed (to prevent the pump from running dry and thus existence damaged), as the well flow rate diminishes during use, the h2o delivery rate may also drop.

Permission requested, Water Ace Corp. Aug 2010 - Pentair Pump Grouping.

Watch Out: Safety warnings are throughout whatsoever pump manufacturer's instructions. Considering some pump models are capable of developing internal pressures of more than 100 psi, if your edifice pipage, pressure relief valves, safety controls, wiring, and plumbing are not properly installed, very dangerous weather including electric shock, tank explosion, and leaks or floods tin occur.

What is the Pumping Capacity in Gallons per Minute for a Submersible Deep Well Pump?

A submersible deep well water pump (the pump is physically within the well and at or close to the bottom of the well piping) can typically raise water from depths of thirty anxiety to hundreds of feet, and at water delivery rates of 4 gpm to 25 gpm depending on the variables that we list beneath.

Submersible well pumps are typically offered in horsepower ratings of ane/2 HP, 3/4 HP, 1 HP, and ane 1/two HP.

Rated water period rates for pumps range (by horsepower and model) from a nominal 6 gpm to 35 gpm.

Lookout out: installing a college capacity well pump may indeed give faster h2o period and college water system pressure, just if the pump is not properly matched to the well'south safe flow charge per unit (by pump pick or pump controls) you can pump all of the h2o out of your well, run dry, harm the pump, etc.

See DEFINITION of Rubber Water WELL YIELD

A nice example table of Deep Well Submersible Well Pump Capacities is provided in the Water Ace 4-inch (diameter) Submersible Well Pump Installation Transmission and excerpted below to illustrate the factors that decide well pump capacity. Nosotros have sharpened the text and provided a larger, more legible tabular array (click to enlarge) than the original.

In selecting a well pump, the well depth likewise every bit water flow requirements must be considered. While jet pumps have a pickup placed typically 5 feet in a higher place the well lesser, when installing a submersible pump, it is placed ten anxiety above the well lesser (maximum) or ten anxiety below the depict downwards limit for the well.

[Click to enlarge any paradigm or table]

[Click to overstate any epitome]

The Water Ace charts (excerpted in part above) make clear that the capacity of a deep well pump to evangelize h2o at a given flow rate varies by the factors we listed previously for both shallow well one line jet pumps and deep well 2-line jet pumps. But this table (above) is for submersible well pumps: the pump is in the well, usually near the bottom.

In the submersible pump capacity table you can run into that the tabular array considers:

• The submersible well pump horsepower
• Variations in submersible pump design
• The depth to the h2o or in other words, the lift that the pump must achieve

Water Ace asserts that a typical 3-4 bedchamber dwelling requires a h2o delivery rate of 8-12 GPM.

Watch out: the water delivery rate at plumbing fixtures is determined past the h2o pump likewise as building water supply pipe and controls. Just it is a number independent of the ability of the well itself to deliver a sustained water flow - the well yield.

Unless a well pump is protected by one or more special devices to prevent the pump from running without water flowing through information technology, the pump tin be damaged or destroyed.

The water commitment rate is also independent of the total quantity of water that tin can be run before you run out.

See WELL FLOW Charge per unit and

see WELL YIELD, SAFE LIMITS

Watch Out: Safety warnings are throughout any pump manufacturer's instructions.

Because some pump models are capable of developing internal pressures of more than 100 psi, if your edifice piping, force per unit area relief valves, safe controls, wiring, and plumbing are not properly installed, very dangerous conditions including electrical shock, tank explosion, and leaks or floods tin can occur.

Readers of this document should also run across the h2o pump types described and our other diagnostic guides for water pumps, wells, motors listed in the "More Reading" department below.

Well Pump Capacity Charts Plot Pumping Head vs GPM Flow Charge per unit Curves vs Pump Horsepower

Reader question: what is the effect of irresolute from a 1/2 hp to a one one/two hp water pump ?

Currently I accept a i/2 hp water pump that will pump 100 gal in 15 min. I am thinking a ane-ane/2 hp water pump will pump h2o 100 gal in 5 min. What will that do to the existing h2o line. I don't know if I have 5/eight" or iii/four" - B.G. one/20/2014

Respond: factors affecting the actual water menstruation rate delivered past a water pump. Check out this case nautical chart plotting water menstruum in GPM against pump motor size and pumping head resistance.

Indeed, B.K., the menses rate through pipe is affected by more than the pump output pressure level,

to include not just

• well pipe or line diameter (typically 1" I.D. or 1 1/4" ID from well to pressure tank and pump)
• merely also friction losses in the piping system which in plough are affected by
• the total length of piping,
• the number of bends or elbows, and
• perchance the presence of constricted fittings anywhere in the run.

[Click to enlarge whatsoever image or chart]

Tabular array adapted from Water Ace data cited in detail at the finish of this article.

Because information technology is located in the well and under-h2o, the work described by a submersible well pump is described as "lift" rather than "building force per unit area". It is the "lift" that overcomes the caput pressure of water in the piping organization above the pump.

The actual effective water flow rate in gallons per minute (GPM) delivered by the water pump through well piping and fittings to the edifice is typically described every bit a curve plotting GPM confronting the pumping head distance in feet, for pumps of diverse horsepower or pumping chapters.

Most water pump manufacturers provide elevator chapters curves for their particular h2o pumps, plotting horsepower and flow rate and lift height as shown in our example nautical chart higher up. - National Wells (2014)

The sample well pump capacity chart at above left plots water pump capacity in gallons per infinitesimal (GPM) (horizontal centrality) against pumping caput resistance in feet (vertical axis) for typical 3450 rpm h2o pump motors in horsepower ranging from 1/2 up to 3 HP. Other well pump capacity charts are in the article above. - Grove Electric (2010), G&G Electric (2010), Water Ace (2010), National Wells (2014)

Typical residential well pumps range in horsepower from one/2 HP to about 2 HP. You tin see in the chart that changing from a i/two HP to a 1 1/2 HP well pump, if we stay at the aforementioned pumping caput resistance and using a 300 ft. caput resistance example, nosotros would see a theoretical GPM flow rate change from 4 GPM upward to around 7 GPM if all other factors remained the same.

To read this nautical chart, follow the 300 Head horizontal line in the chart across from where it crosses the 4 GPM line on the 1/2 HP pump curve over further to the right to see the i 1/two HP pump (two models) touching or shut to the 300 Head Resistance line at 7 GPM.

If for theoretical statement we exclude other snafus like chock-full pipage or a low-flow-rate well, the lift distance or head against which the pump has to piece of work is the almost significant factor equally pump lift chapters varies by pump horsepower and type and location.

Water Pump Size Requirement Calculation - Definition of head pressure or Full Dynamic Head (TDH), Vertical Rise, & Friction Losses in Piping

Yous have not specified if your well pump is a submersible or is an above basis unit, nor among in a higher place ground units did you specify if this is a one line or 2-line jet pump - or a different pump blazon. Equally we don't know any of that data, nor the well pipe diameter of your installation, its length, bends, etc. a fixed answer would be mere arm-waving speculation.

A well pump needs to be matched to the flow rate chapters of the well itself - lest the pump merely run out of available water, a condition that risks pump damage equally well every bit loss of edifice water supply.

The well pump also needs to be matched against the lift required - how far h2o must be lifted from the bottom of the submersible pump in the well to the water pressure level tank and controls in the building. Water pump lift can be defined as the force required to overcome the "caput pressure" measured in feet.

To accurately compute head pressure, expressed equally Total Dynamic Caput or TDH, the designer adds the pumping level or pinnacle that h2o is moved within the well, the additional vertical rise from water top to terminal destination, and the friction losses in the pipage organisation.

In the article to a higher place, we evidence tables and charts helpful in determining the required size in HP required for a water pump in a given installation. I recommend against choosing pump size arbitrarily for reasons I cite below: cost, operating life, as well every bit capacity requirements.

Recapping, calculations of required water pump size consider:

• The vertical rise that the pump has to motility h2o
• The horizontal pumping distance that water must be moved
• The friction losses in the piping arrangement - a part of pipe diameter, number of fittings or elbows, and possibly other more subtle factors

  Friction losses also include losses as h2o flows through valves or controls, check valves, tees, couplings. Engineers & other well and pump experts apply tables that express the outcome of valves and fittings on water flow equally equivalent length of pipage in feet. For case, the resistance imparted by a 1-inch diameter plastic or steel 90 degree pipe elbow is equivalent to about three feet of pipe.

• The water quantity usage rate - maximum usage anticipated in the building

  Run across WATER QUANTITY USAGE TABLES for details.

Watch out: none of the topics listed in your message or in pump GPM capacity above address the potentially decision-making effects on water flow rate at a given fixture caused by in-edifice piping, valves, clogs, etc. Something as simple as a clogged faucet strainer volition significantly cut water flow rate there - a problem for which the trouble and expense of changing to a larger horsepower water pump would be very much the wrong "fix".

What y'all can infer is that you are tripling the pump horsepower - which is a big leap, so it would be reasonable to expect a significantly increased water menstruation rate - all other components being equal.

Watch out: in some cases of a poor flow-rate well, information technology is the well'due south recovery charge per unit or flow rate that limits the water menstruation rate at the building (unless a large buffer storage tank of water is also installed). In such cases, installing a more powerful pump will only exhaust the well more quickly, leading to loss of h2o supply entirely.

And a final alarm:

Scout out: be sure that you take an accurate idea of the trouble and costs involved in tripling the well pump horsepower.

A alter from a smaller one/2 hp pump to a 1 ane/ii hp model may require electrical wiring changes of wire size or gauge and perchance a change from 120V to 240V service along with appropriate changes in pump controls and switches - all adding to the toll of installation of the new pump.

In sum, I'd want to have a more accurate description of the water menstruum trouble in your building and of the causes of any poor water flow complaints before hopping to install a new larger well pump.

Number of submersible well pump stages decide pump lift capacity

For submersible well pumps, typically college HP pumps also are designed with a greater number of pumping stages - mechanical impellers that increase the elevator capacity of the pump. Beneath are some submersible pump pattern stages and horsepower ratings:

Table of Submersible Pump Stages vs HP vs Full Dynamic Head vs. GPM Menstruum Rate Capacity
Water Pump HP	Nr. of Pump Stages	TDH Capacity	GPM Menses Rate Capacity
1 HP	8	0 - 200 Ft.	4 - 40 GPM (varies by TDH)
one one/2 HP	xi	0 - 399 Ft.	four - 40 GPM (varies by TDH)
ii HP	14	0 - 350 Ft.	four - 42 GPM (varies by TDH)
3 HP	19	0 - 500 Ft.	4 - 43 GPM (varies by TDH)
five HP	28	0 - 700 Ft.	4 - 43 GPM (varies by TDH)

Notes to the tabular array above

The data in this table is for example purposes. Actual pump capacities vary by model, manufacturer, design, and installation details.

• Source: adapted from A.Y. McDonald Co. Mfg. (2014)
• API-Ferguson, Zoeller Pumps, Flint & Walling, Four-INCH SUBMERSIBLE PUMP Itemize [PDF] (2012) Flint & Walling, 95 North Oak St., Kendallville IN 46755 U.s., Tel: 800-345-9422, Spider web: flintandwalling.com retrieved 2022/02/24 original source: https://api.ferguson.com/dar-step-service/Query?ASSET_ID=1352800&USE_TYPE=SPECIFICATION&PRODUCT_ID=496013
• AY McDonald Mfg, Water PUMP SIZING Nuts, HOW a CENTRIFUGAL PUMP WORKS [PDF] A.Y. McDonald Mfg. Co 4800 Chavenelle Road Dubuque, IA 52002 U.s.a., Tel: 800-292-2737, Website: www.aymcdonald.com Email: pumps@aymcdonald.com. Includes the basics of how to cull the proper pump and explains how the matched nozzle and ventyuri in the jet ejector function; retrieved 2020/02/18 original source: http://www.midc-ent.com/Pump%20Basic-Sizing.pdf

  Excerpts:
  The head or pressure level that a pump volition develop is in direct relation to the impeller diameter, the number of impellers, the eye or inlet opening size, and how much velocity is developed from the speed of the shaft rotation. Chapters is determined by the exit width of the impeller.

  All of these factors affect the horsepower size of the motor to be used; the more h2o to be pumped or pressure to be adult, the more energy is needed. A centrifugal pump is not positive interim. As the depth to water increases, it pumps less and less water.

  Besides, when it pumps against increasing pressure, it pumps less water. For these reasons information technology is important to select a centrifugal pump that is designed to exercise a detail pumping job.

  The jet and venturi ... accept to be well engineered and carefully matched to be efficient for various pumping conditions. The jet nozzle and venturi are as well known as ejectors/ejector kits.

• Franklin FPS SUBMERSIBLE PUMPS, RESIDENTIAL, LIGHT COMMERCIAL Catalog [PDF] (2016) Franklin Electric, FPS, Cost free: 800-269-0063 Fax: 260-827-5800 E-mail: cleanwater@fele.com Website: franklinwater.com TECHNICAL SERVICE HOTLINE Please contact united states at: Cost gratis: 800-269-0063 Fax: 260-827-5800 Electronic mail:
• Hammelmann Corporation - Headquarters 436 Southpointe Drive - Miamisburg, OH 45342 USA Tel: 937-859-8777 Email: post@hammelmann.com

  Hammelmann provides a water jetting calculator online too every bit a downloadable app: http://www.hammelmann.de/us/produkte/anwendungstechnik/app/water-jetting-calculator.php

• IHS, SUBMERSIBLE PUMP SIZING & SELECTION [PDF] Indian Health Service, U.Southward. Federal Health Program for American Indians and Alaska Natives, 5600 Fishers Lane, Rockville, MD 20857 U.s., retrieved 2020/02.eighteen original source: National Exploration/ Wells/Pumps, presentation https://world wide web.ihs.gov/EHSCT/documents/sfc_webinar_docs/2013-Pump%20Sizing%20With%20Exercises%20r1.pdf

  Includes table of friction losses in well piping as well pump performance curfes and caput lift vs pump chapters in GPM.

• Pemberthy/ Tyco JET PUMP APPLICATION GUIDE [PDF] (2005) Penberthy / Tyco, 320 Locust Street, Prophetstown, IL 61277 U.s.a., Tel: (815) 537-2311 Website: www.penberthy-online.com • E-mail: penberthysales@tycovalves.com

  retrieved 2020/02/18, original source: http://alliedindustrialsales.com/wp-content/uploads/2012/03/Penberthy-Jet-Pump-Application-Guide.pdf

  Excerpt: Jet pumps, too known as eductors, operate on the principles of fluid dynamics. An operating fluid media, which is referred to as the MOTIVE, placed under pressure enters the inlet and is forced through the nozzle where it is converted into a high-velocity stream.

  This high-velocity stream decreases the force per unit area in the suction chamber, creating a partial vacuum that draws the suction material into the bedchamber where it is entrained by the motive media.

  Once the SUCTION stream is drawn in, shear between motive media and the transported material causes both media to be intermixed and pumped out the DISCHARGE outlet, dispelled at a force per unit area greater than that of the SUCTION stream but lower than that of the MOTIVE. This basic principle of fluid dynamics is what makes Penberthy jet pumps work.

• Red Panthera leo 1-2-3 EASY GUIDE to PUMP & TANK SELECTION [PDF] RedLion Products, United states of america 9255 Coverdale Rd. Fort Wayne, IN 46809 United states,

  Red Lion Canada Customer Relations: 61 Parr Blvd, Unit 1 Bolton, ON L7E 4E3

  Tel: 888-885-9254, Email: techsupport@fele.com Website: https://redlionproducts.com/ retrieved 2020/02/18 original source: https://redlionproducts.com/media/33881/996245_rl-pump-and-tank-selection-guide_web.pdf

Reader Q&A - likewise run across the FAQs series linked-to below

@Allen,

You lot are increasing the planned total water usage quantity and charge per unit for your property; knowing the well's flow rate and recovery-rate are probably more than critical than the well pump's GPM rate. Those are discussed in the articles I've recommended.

@inspectapedia.com.moderator,

I am trying to measure the existing organization, every bit we are adding on a new cottage and landscaping. Hopefully, not thinking about a new pump.

@Allen,

What problem are we solving hither? Measuring the existing system or guessing at the capacity of a replacement pump;

Sure it'south informative to measure flow rate at the well, but that'southward non telling us what the pump'south original rating data were.

And then we're still not quite comparison actual pump specifications.

IMO if your question is "what GPM h2o menses charge per unit am I going to get from a new pump"

then you demand to know well depth or / and total elevator peak, and
of course
you really need to know the well'due south flow rate since it doesn't matter how fantastic a pump's capacity is if it pumps the well dry.

Meet our WELL FLOW RATE articles in the Alphabetize to Related Articles given at the end of this article.

@inspectapedia.com.moderator,

Thank you for the information. Unfortunately, the well company does not take records from 25 years agone on the 1 HP pump they installed.

They suggested disconnecting the water line from the well to the house (they used another term for this), and just filling 5 gal buckets direct from the well, and run across how long information technology takes to fill them.

@Allen,

You lot'd remember maybe and then, but no, non really.

You need to read the specific pump flow characteristics for the specific make and model and type (to a higher place basis two line jet pump, 1 line jet pump, submersible pump) of the same voltage;

For example a brand A 1hp well pump with a 50 foot total lift and all other piping details identical, pump l gpm while some other pump make B 1hp well pump with the same lift and pipe details might pump 40 gpm.

We need to get specific.

But you lot tin go a GENERAL answer comparing well pump GPM capacities from tables given above on this page.

You'll run across that when you lot plot pump HP and elevator confronting GPM capacity the results are plotted in curves, not a straight-line linear function such as your example would suggest.

Original well pump was one-1/2 HP with a flow of 60 GPM. Would the flow with a i HP motor be 40 GPM?

@Khanh,

sure just utilize the on page search box higher up to find our articles on SUMP PUMPS to see the type of pump you need and several options.

Hullo
I have a slanted driveway 20 ft X 40 ft. We congenital a drain 3X4X20 at the end of the bulldoze way. When it rains our bleed fills and floods our garage. We put a 1/three HP utility pump and it helps, however can any ane recommend a pump we can use?

I was looking at a 1 HP models, but can't observe a skillful i. Nosotros have a outlet outside, and nosotros submerge the pump in the drain. Nosotros push water back upward using a garden hose to the street. Thanks for your help.

@Bob Kuhl,

On the page above you will see a colored line chart with pump capacity curves that go to & beyond the depth in your case, delight take a look at

Well Pump Capacity Charts Plot Pumping Caput vs GPM Flow Rate Curves vs Pump Horsepower

What is GPH for iii HP (10CS30) Gould well pump. The well is about 850 ft. and the pump is set almost 725 feet.

@David,

In the article in a higher place on this folio, in the department on deep well submersible pumps, you will find a squeamish table that compares lift capacity with pump size or horsepower and gallons per minute of water flow.

The table include depths to five hundred feet.

My well meridian is 198 ft it's 100' to 150' deep I am pumping information technology up to a storage tank that is at elevation of 505' how many hp submersible pump do I need

@Diego,

yes probably, but ...

Watch out:

1. at that place is a risk that y'all pump water out of the well faster than its recovery rate- running the well dry out and damaging the pump; you demand toknow your well'south catamenia rate or capacity to deliver water continuously (see Period Examination in the Article INDEX)

two. at that higher horsepower you will probably take to run new electric ability to your well and will demand new controls - probably a carve up Hard disk 220V relay

can i replace my homes ane/2 or 3/iv hp sumersible pump with a 2 h/p 220 volt 42 gpm submersible pump. I similar to install a few sprinklers don't know how many. Well is 250ft deep. Never had a storage of h2o. I accept a storage tank and a thirty/50 pressure level switch.

@Wade I.,

There are certainly portable gas powered h2o pumps similar the Honda WX10TA that tin pump at higher rates (that model claims 32 gpm)

Sentry out: still to take a much closer expect at the pump's intended use and at the result of pumping distance and head on its GPM rate. For instance the WX10-TA shown here comes with a sixteen foot hose
and

- has a pumping suction lift head limit of 26 ft

- has a total caput lift capacity of 121 Feet

- uses a 1" inlet and outlet

and I'm non confident of its heavier duty use over a longer or more than regular interval much less over a long pumping altitude.

If you can go power to the pumping site, I'd expect at a submersible pump that tin can deliver water perhaps at a slower charge per unit but as you lot suggest, over a longer interval, filling storage tanks.

There is a tremendous number of portable, gas-powered water pumps, some of very high capacity, some used for transfer, for trash liquids, and for fire-fighting (higher delivery pressure, smaller diameter hose);

Information technology's worth noting that beyond manufacturers a number of pumps use Honda engines,.

Look at transfer pumps and irrigation pumps.

Cheers for the aid If a gas powered pump could evangelize x gpm that would suffice. Notwithstanding, we've too considered using a submersible electric pump to make full the holding tanks rather than a gas powered pump.

Nosotros have decent flow to our business firm from a 200' deep alkaline well located appx. 400' horizontal and 80' beneath our house, by fashion of a submersible. Bottom-line: we're non so concerned with how quickly the two tanks get filled as the alternative is hauling fresh water 200 gal. at a time from a public source that's 7 miles away - which BTW takes about 7-8 hours to accomplish.

@Wade I., If you lot have a expect at the pump performance charts and curves given in the article in a higher place. you volition see that none of the residential water pumps are capable of delivering thirty or 40 gallons a minute much less at the pumping caput that you lot describe.

We're going to need to look for a commercial gas-powered pump with that chapters. Let's both research further in the commercial range. I'll see what I tin discover.

I think with that pumping rate you lot're likewise going to want to take a await at the pump duty cycle.

I need to pump water from a river that is 500' horizontal plus 100' vertical from two 600 gal. belongings tanks locateded near our house. What size gas pump/hose combination would I need to accomplish a ten, twenty or 30 gpm menses rate.

@chris,

Whatever ii-line jet pump or submersible pump - encounter the pump lift capacity and gpm tables in the article higher up, Chris.

What Goulds pump do I need to pump h2o up from a deep well to 60 plus feet

Virgil,

I think that the power to vary pump output is different across Brands and models. For your present circumstance I would consider either installing a suitable pressure tank to terminate the short cycling problem Or having a conversation with technical back up at the manufacturer to see if they will permit Command that will vary the pump speed and output.

I replaced a 2HP submersible pump with a 1 1/2HP submersible pump with a 35 GPM wet end hoping to achieve near 43 GPM considering the 2HP pump was delivering 60 GPM which is more than I want.

Instead, I am achieving sixty GPM and the well itself is only producing l GPM thus the pump is out pumping the well and the pump saver is repeatedly stopping and starting the pump. I was told past my well tester that the 1 i/2HP pump with a 35 GPM wet end would requite me 42 or 43 GPM which is what I want.

How is it possible that it is pumping threescore GPM and what tin can I do near information technology?

How long can a lancaster sumersible deep well 3/iv hp pump run without water an volition not damage the pump itself

Jon

Y'all tin can certainly measure the PSI that your pump delivers against a closed system but beware of injuring yourself if yous burst a pipage or a pressure level tank or any other pressurized device. I think if you're watching the pump pressure and you don't allow it become much higher up 65 PSI you're not going to destroy the pump during the test. Just don't allow information technology run for prolonged period of time or overheat.

I believe information technology's a Sta Rite, pump. Submersible. 7.five HP. Runs a wheel line system, with 33 heads. 30psi with some leaks. Well is sixty feet deep, eight Inch casing, 4 Inch main to pump. Specifics are unavailable, without pulling pump, even so, I'g certain pump is 7.5. HP.

Am told, 'with leaks stock-still' psi would reach around 45psi. Water table remains at fifteen anxiety at all times. To have any more than data, would require removal of pump.
Pump had been replaced years earlier,without any manuals available, receipts and the like.

Control panel remained and was used with new pump, strongly suspected to be a Sta Rite.
Control panel stats are as follows,

Model CP6K02,,,
Serial 1D77 (Apr, 1977) Just this existing pump was replaced in early on 1990'southward with ane that works with this control panel
Volts 230,,, three wires, one is ground.
many numbers faded at this indicate, but, "RPM 3450", PH 1 Single stage,

,,,Max amp 44.6,,,,SF-1.2
and so, '1118-1285',,,,235-1652 'both'
metal capacitors made by 'Mallory'
3.5 MFR
370 volts ac

sixty degree centigrade five-c, or perchance,,,'cvc'
"xviii Inch" with perhaps more than faded inl numbers below the '60 degree centigrade' mark.

And so, the question is, is at that place enough information here, to make up one's mind if this pump is capable of running a 'Big Gun Sprinkler Head', that requires 65 psi to operate? The idea would be to plug off plenty sprinkler heads and 'leaks', in order to accomplish that 65 psi and run the gun.

Based on this info, do you guys suppose that would work or could such loftier psi pressure level ruin the pump?

Was told I could crank down valves, look until I accomplish 65 psi, then measure how fast I fill a fifty gallon butt and so they could calculate whether or non pump would run that Big Gun nether these conditions. I'm just a niggling nervous about fifty-fifty trying that, obviously I would not want to ruin the pump and am non certain of the earlier exam suggestion.

Can y'all weigh in? Whatsoever advice? And thank you even though I'grand sure information technology'southward something of a thankless job, it certain isn't with me. Jon

Cheers for an interesting question.

Nobody can give a completely-accurate reply to your question as yous pose it because we don't know the pumping chapters of your pump in gpm - though y'all might get shut to that past identifying the pump make and model and then checking it'southward owner's manual.

There you'll come across that the pump'due south output is affected by at least six factors that we list above in the article on this page.

And on this aforementioned page in our section titled "What is the Pumping Capacity in Gallons per Minute for a Submersible Deep Well Pump?" you'll see that a typical 1hp submersible pump with a 20 ft. lift with an average of 40 psi output might pump around 40 gpm. From at that place you can do the math.

Sentry out: even so as y'all'll meet in our pump chapters tables on this folio, the pump'southward output varies a lot by pump model, even when the horsepower and all other factors remain the same.

I take a shallow well ( 25ft ) submersible 1 h.p. pump sucking from about 20ft deep.

I am pumping through a 2" pvc piping with no restrictions - merely gratis flow for a length of most 200ft into a pond pool.

Pump pressure level is 40-sixty psi . I can pump for nearly 1 hour before the water level drops from the well full level ( 10 ft ) down to 20 the 20 human foot level ( simply above the pump intake level )
How many gallons per hour am I pumping ?

See this itemize that gives pump chapters taboes for Franklin Electric's submersible pumps:

FPS SUBMERSIBLE PUMPS, RESIDENTIAL, Light COMMERCIAL CATALOG [PDF]

You'll see htat you will want the pump model name and model general rating, such every bit iv" Serial V Pump, x gpm (catalog p. 32).

For that Instance which is NOT YOUR PUMP, we see this typical table of pump chapters in U.Due south. gallons per infinitesimal.

This pump, at 1.5hp (not necessarily your model) at thirty ft. is pumping aroun d xiii gpm.

I have a Franklin motors1.5 horsepower pump at xxx feet deep with a ii-inch line. How many gallons per minute will that produce?

That sounds every bit if

Your pump motor is failing

or

The pump wiring is nether-sized for the lengfth of run

I have 1HP deep well pump that cannot run continuously due to sudden subtract in power supply (230 volts to 115 volts when pump starts running). Well depth is 140 ft and casing is 4 inches. Please propose what should I do. Will Auto Voltage Regulator help? Thank you.

Joyce,

Typical pressure rangess are 20/twoscore psi or 30/l psi.

What is the PSI for a 3/iv horsepower submersible pump.
6 inch pipe
Well is 100 anxiety deep

Thank you

Equally all-time I tin answer: the horizontal pumping altitude that your pump can push button water doesn't drop to zero, but rather the longer the piping the slower the pumping output rate will exist in gpm.

The pump capacity tables given above on this page give more-specific answers for various well pump depths and piping diameters and pump horsepower but yous will want to observe the pump capacity table for your specific pump make and model.

Keep in mind that it is the lift, not the horizontal distance, that is the hardest piece of work that the pump has to do, and so information technology'southward the pump depth (probably something less than the 120ft. depth of your well) that is criticial.

I purchased a piece of property with a well (120 feet deep, 6 inch casing, 3hp well pump in the well).

I understand that the 3 hp well pump will need 9kw power source to bulldoze the pump. How far will the pump push the column of h2o in a 2 inch line?

The effect of the height to which your pump has to lift h2o is to reduce the pump's output rate; information technology won't fall to zero except in extreme cases.

Then you add together together the peak of the colina PLUS the depth of the well from which water has to be lifted.

Then notice the pump capacity table for your specific well pump brand, type, and model and you'll encounter its rated output capacity in gph or gpm.

In a higher place on this page our table titled

Table of Submersible Pump Stages vs HP vs Total Dynamic Caput vs. GPM Period Rate Chapters

has some sample data. For example, even a pump smaller than yours, say a 5 hp. submersible, will have an output rate that might fall from 43 gpm to four gpm if information technology has to face a full elevator of 700 ft.

You need to ID the specific pump brand and model besides as the total elevator height to be able to get the pump'south output rate in GPM at a specific height.

Take a look at API-Ferguson, Zoeller Pumps, Flint & Walling, Four-INCH SUBMERSIBLE PUMP CATALOG [PDF] (cited in detail above on this page)

and you'll see a 7 ane/2 hp F&W pump with 23 stages can elevator h2o as much as 700 ft total vertical distance, with a flow rate of about 24 gpm at a 20 psi output pressure.

we have a 7and half hp submersible pump pumping through a 4 in line . how high a colina can it go over?

Y'all'll see in the pump output chapters tables we give on this page that yous need to specifiy a few more parameters, such as the desired delivery pressure.

A 70 meter deep (230 ft deep) well tin can be served by a 2 hp. submersible pump delivering about xxx gpm merely at close to zero discharge pressure!

To get to a 20 psi discharge pressure a typical submersible in the 3 hp. range tin evangelize 35 gpm, and at 40 psi discharge pressure, the same pump will evangelize about xxx gpm.

Other readers: see the Flint & Walling case pump output chapters tabular array we show just above on this folio.

what size of submersible pump would i need if the borewell is 70meters deep and has an estimated yield of 20 liters pr minute? the distance from the well to the tank is 100 meters.

Bob

Exist sure that you ready the h2o pressure tank AIR pre-accuse to 2 psi below the pressure control switch Cut IN pressure setting,

AND that the pre-charge is done with the pump off and all water force per unit area relieved from the system.

I cannot go the pump to run unless information technology runs 22 psi on to 68 psi off. with tank at 18 psi. switch is set at 30 psi on and l psi off.

Andy

The book in gallons per minute of a 1HP pump will vary depending on important variables including

- pump type (i line jet, 2 line get, submersible)

- pump lift superlative - how high does the pump take to lift wter

- pipe diameter and other restrictions similar elbows and valves

so there's no unmarried "right" respond.

But to give a reasonable example,

a 1 hp. submersible well pump - varying by model - can deliver 10 gph while lifting water from a 200 ft. deep well.

a ane hp submersible well pump - varying by model - tin can deliver 23 gpm at twoscore foot lift, down to 14 gpm if that same pump has to lift h2o from greater depth.

Accept a expect in the article above on this folio and you'll see a table of typical well pump capacities that map

- pump horsepower
- pump elevator summit (or depth)
- gpm of h2o delivered

How much volumn of h2o will 1 quarter Hp pump put out ?

Probably easiest is a submersible well pump with sufficient horsepower, every bit you'll read in the article in a higher place on this page. You may need multiple check valves on the well pipage as well.

What kind of pump should i use to lift water from the source which is nearly 400 meters+- below the basis?

Shiddeshar,

The horizontal distance and pipage diameter should non bear upon the pump requirements unless the friction and other losses (such as from many elbows or bends in pipage) are unusually great.

Beyond that bespeak,

It'due south not just the pump horsepower that is important to get water lifted sixty feet from a h2o source.

Information technology is as well the type of pump.

A one-line or unmarried-line jet pump can only lift water almost 7.5 meters or 25 feet.

A 2 line jet pump of the aforementioned horsepower will accept no trouble lifting h2o 60 feet.

Finally, the larger pump will deliver a faster h2o flow charge per unit in liters per minute, only

watch out: if the pump rate out of the well exceeds the well's h2o in-catamenia rate so you'll pump the well dry.

Sir my question is.:in my farm pipeline is 90mm lenth is 1700 feet and height is (from starting point to terminate point)50to sixty feet pumpset is 7hp then for which pumpset i buy for beter flow of h2o for agri in river and which blazon of valve i utilize for no comes pressure on pipeline i am a farmer and full land is ten hector in this place

...

Go along reading at SUBMERSIBLE PUMP TORQUE Problems & SOLUTIONS or select a topic from the closely-related manufactures below, or see the consummate Article INDEX.

Or see WATER PUMP Capacity & GPM FAQs - questions and answers about pump chapters posted originally at the end of this page.

Or come across these

Water Pump Articles

• Water PUMP REPAIR GUIDE - domicile
• WATER PUMP CAPACITIES TYPES RATES GPM
  • TREADLE PUMP CAPACITIES & USE
  • Water PUMP, I LINE JET
  • WATER PUMP, SUBMERSIBLE
  • SUBMERSIBLE PUMP TORQUE Bug & SOLUTIONS
  • H2o PUMP, TWO LINE JET
  • WATER PUMP, Ii LINE JET OPERATION
  • Water PUMP Force per unit area SENSITIVE
• WATER PUMP WONT STOP RUNNING

Suggested commendation for this web folio

Water PUMP CAPACITIES TYPES RATES GPM at InspectApedia.com - online encyclopedia of building & environmental inspection, testing, diagnosis, repair, & problem prevention advice.

Or see this

INDEX to RELATED ARTICLES: Commodity Alphabetize to WATER SUPPLY, PUMPS TANKS WELLS

Or utilize the SEARCH BOX found below to Enquire a Question or Search InspectApedia

...

Ask a Question or Search InspectApedia

Endeavour the search box just below, or if you prefer, post a question or annotate in the Comments box below and we will respond promptly.

Search the InspectApedia website

Note: appearance of your Comment beneath may be delayed: if your comment contains an image, web link, or text that looks to the software as if it might exist a web link, your posting will appear after it has been canonical by a moderator. Apologies for the delay.

Technical Reviewers & References

Click to Show or Hide Citations & References

Publisher InspectApedia.com - Daniel Friedman

What Size Pump Do I Need To Lift Water 400 Ft,

Source: https://inspectapedia.com/water/Well_Pump_Capacity.php

Posted by: smithweriatere.blogspot.com

Share this post